Oxidation of sulfur (IV) by oxygen in aqueous solution: role of some metal ions

Journal of the Brazilian Chemical Society

Cabral Neto, Clodovil A¹  Andrade, Jailson B. de¹  Universidade Federal da Bahia, Salvador, Brazil¹  Alves, Janete J.F.¹  Martins, Claudia R.¹ 

关键词: catalysis;    aqueous S(IV) oxidation;    transition metals;   

DOI  :  10.1590/S0103-50531999000600006

学科分类：化学（综合）

来源: SciELO

【 摘 要 】

Typical urban atmosphere consists of a variety of anthropogenic air pollutants with particular regard to sulfur species in which dioxide is a major atmospheric pollutant1. The main sources of SO2(g) emissions are the burning of fossil fuels (e.g., power plants and mobile sources) and the smelting of ores rich in sulfur. In the atmosphere, SO2(g) can react with various oxidants (e.g., O2, O3, H2O2, NOx, OH radicals) to form sulfate aerosol, either as sulfuric acid droplets, or as neutralized particles such as ammonium sulfate, which play a special role in atmospheric processes like acid rain and visibility degradation1,2. There is evidence, however, that a significant portion of the airborne S species emitted to the environment may be particulate SO32- 2 . This species has long residence times in the environment. It is known that SO2(g),at the temperature of 400 °C, reacts very slowly to produce SO3(g). In this way, the SO2(g) oxidation to sulfate aerosol, in the atmosphere, either homogeneously in the gas phase or heterogeneously in atmospheric microdroplets must be associated with other reaction processes such as photochemical oxidation or catalytic oxidation2. These processes depend on a variety of factors such as intensity of incident solar radiation, relative humidity and, especially, the presence of transition metal ions which play a recognized role as catalysts3,4. The oxidation of sulfur (IV) (SO2 .nH2O, HSO3-, SO32-) to sulfate, catalyzed by transition metal ions in aqueous microdroplets, has been acknowledged as a viable, non-photolytic pathway, for the production of H2SO4 in fogs, clouds and humid atmospheres4. This has been studied systematically for more than one century, without a consense on the existence of a pH dependence, reaction rates and mechanisms, resulting in numerous and sometimes contradictory reports4. On the other hand, there is significant lack of information on either the behavior and the role of the transition metal on the catalyzed reactions, and much of the work was performed involving both S (IV) and transition metal ion concentrations several times greater than that found in typical urban atmosphere4,5. It has been known that some transition-metal ions are able to catalyse or initiate the aqueous oxidation of sulfur (IV). The variation of catalytic abilities of the transition metal ions may be understood in terms of the accessibility of multiple oxidation states and the activation of metal ions in the high valence state. For a metal ion to be catalytically active, it must be able to ascend to a sufficiently high valence state to extract an electron from a S(IV) species, and thereby generate active intermediates which can propagate the reaction6. It seems to be generally accepted though that iron (II/III) and manganese (II/III) are the most efficient catalysts. An important aspect concerns the question of how the reduced metal ion species are reoxidized in order to complete the catalytic cycle. Some authors suggested that Fe(II) is oxidized back to Fe(III) by reaction with some of the radical species formed in the radical chain mechanism7. The reports on oxidation of S(IV) catalyzed by transition metals are usually centered on metal ions such as: Mn(II), Fe(III) and Cu(II)5 in the presence of O2 saturated aqueous solution. In this work we investigated the role of Cr(VI), Cr(III), Cd(II), V(V) and Cl- ions on the oxidation of S(IV) by oxygen in the aqueous phase. The transition metal ion concentrations were chosen in order to represent their soluble fractions in urban aerosols8. The experiments were driven in the sense of determining the equations rates and their dependence on the pH and activation energy.  Experimental MaterialsAll chemicals used in this study were of analytical reagent grade and all solutions were prepared using distilled water further purified in an E-pure system (Barnstead). Fresh solutions of CrO3 , CrCl3 , CdCl2., NH4VO3 and NaCl were used. The calibration curves for S(VI) and S(IV)) were made using stock solutions of K2SO4 (1 mg mL-1) and Na2S2O5 (1.2 mg mL-1 in formaldehyde 10-2 mol L-1) in acetate buffer (2 mmol L-1). For the kinetic studies a fresh solution of Na2S2O5,(1.2 mg mL-1 without formaldehyde) was used. To adjust the pH, solutions of NaOH (0.1 mol L-1) and HNO3 (0.1 mol L-1) were used.ApparatusA Digimed Model DMPH-2 pH meter and an Analyzer 2 A13/AM microglass electrode were used for pH determinations. The measurements were performed at 25 °C and 35 °C. The clean air (as source of O2 ) was generated by a Zero Air Supplier (Thermo Environmental, Model 111). The concentrations of S(IV) and S(VI) were determined using an ion chromatograph (IC) Dionex (Model 4000 i) equipped with a Rheodyne injector with a 20 mL sample loop and a conductivity detector at 10 mS. The analytical column used was a Dionex AS9-SC followed by a fibrous micromembrane supressor Dionex AMMS-1. A 1.8 mmol L-1 NaHCO3 + 1.7 mmol L–1 Na2CO3 eluent was used at a flow rate of 1.5 mL min-1. Different concentrations of S(IV) and S(VI) solutions, in the range of 1.0 mg L-1 to 5.0 mg L-1, were injected in the ion chromatographic system, and the peak heights obtained were plotted against concentration. The IC determination was completed in about 7 min (Fig. 1) and no interferences were observed in both S(IV) and S(VI) retention times.  ProcedureThe kinetic studies were conducted in a laboratory reactor, which consists of a 500 mL round-bottom with three-neck (24/40 joints) thermostatized by means of a water bath (Fig. 2). The three inlets of the reaction flask were used: (2) rushton type turbine impeller; (3) introduction of reagents and (4) introduction of gas. Aliquots in the range of 1 to 3 mL of metal ion solution were introduced into the reactor and the pH was immediately adjusted by addition of variable amounts of NaOH or HNO3 0.1 mol L-1 solutions. Then, 1.0 mL of fresh aqueous S(IV) solution (1.2 mg mL-1) was injected into the reactor at time (t = 0). The total volume of reaction solution was adjusted to 150 mL and the initial concentration of S(IV) was set at 8.0 mg. L-1. Then, the air was continuously bubbled through the aqueous solution at a flow rate of 1.0 L min-1. A mass flow meter was used to control the flow rate. Both gas and liquid phases were well mixed in the reactor.   Aliquots of 1 mL were taken after certain time intervals, and 1mL of formaldehyde solution (10-2 mol L-1) was added immediately in order to quench S(IV) oxidation9,10. In this way, the oxidation reaction was stopped by the formation of hydroxymethanesulphonate according to the following reaction (Eq. 1):Once a stabilized solution was injected into the ion chromatography system, the signals of sulfate and sulfite (decomposition product of hydroxymethanesulphonate in mobile phase, basic media) were measured, and the concentrations of S(IV) and S(VI) were determined using the corresponding calibration curves. For comparative studies the oxidation reaction of S(IV) was followed under different circumstances, which consisted of passing clean air flow through the S(IV) solution, in the absence of transition metal ion or chloride ion. Figure 3 represents the oxidation by O2 in the absence of transition metal (Fig. 3a) and in the presence of Cr(IV) (1 mg L-1, Fig. 3b). The difference in the half-life time, in the two systems, is approximately 26.  Results and Discussion The oxygen used in this study was that of ambient air. Its solubility in pure water can be described by Henry’s law (Eq. 2):where: c = concentration of a gas in solution (mol L-1atm-1), pg = partial pressure of a gas (atm), p = total gas pressure above the solution in equilibrium (atm), H = Henry’s constant (mol L-1 atm-1), Yg = mole fraction. If other substances are dissolved in the solution (e.g. Na2SO3, Na2SO4, NaCl) the solubility of the oxygen decreases due to salting-out effect, and may not follow Henry’s law4. The oxygen solubility in pure water, at 25.0 °C, reported in the literature, is 1.27 mmol L-1 11,12 and this value did not show significant changes in the presence of Na2SO3 50 mmol L-1(1.25 mmol L-1) 13, which is compatible with the present study (Na2SO3 0.25 mmol L-1). The rate constants for non catalyzed oxidation reactions of S(IV) were determined by passing clean air flow through the S(IV) solution, in the absence of transition metal ion or chloride ion. Special attention must be paid to the purity of the water, because traces of transition metal, which remain in the water as a result of deficiencies in the purification process, can enhance the rate constant. For example, differences in rate constant values (determined at 25.0 °C and pH 8.2-8.9), seven times slower, were observed for the non catalyzed reaction when using Milli R/Q water (1.3 x 10-5 s-1) instead of deionized water (9.5 x 10-5 s-1)14. In this study, the determined value (25 °C and pH range 2.1-4.5) was 8.0 ± 0.5 x 10-4 s-1. This value was used throughout this study as a non catalyzed constant for the oxidation reaction rate.Chromium (VI)The two oxidation states of chromium commonly found in the environment are trivalent chromium, the predominant species in the atmospheric aqueous phase, and hexavalent chromium, a powerful oxidizing agent, for which the rate reaction with S(IV) decreases with decreasing acidity15. In this way, the reaction rate for catalyzed aqueous S(IV) (8.0 mg L-1) oxidation was studied in the presence of Cr(VI) at three different concentrations (0.2, 0.5 and 1.0 mg L-1), at a pH range of 2.0 - 4.5 and temperatures of 11.0, 25.0 and 35.0 °C. In all experiments the Cr(VI) concentration was, at least eight times lower than the S(IV) concentration. At the end of the experiments, at least, 80% of the initial Cr(VI) concentration remains in the same oxidation state. Figure 3 represents the S(IV) oxidation by O2 in absence of transition metal (Fig. 3a) and in the presence of Cr(IV) (1 mg L-1, Fig. 3b). The difference in the half-life time, in the two systems, is approximately 26 times. The reaction order16 was obtained graphically by plotting -ln[S(IV)/[S(IV)o] versus the reaction time. The plots indicate the first-order dependence in relation to S(IV) concentration, Fig. 4. From the slopes, the apparent constants (k’) were determined. It was observed that k’ is proportional to the Cr(VI) concentrations, Fig. 5. Thus, this kinetic behavior indicates also that the S(IV) oxidation in the presence of Cr(VI) is of first-order in relation to Cr(VI) concentration. According to experimental data, the following rate Eq. (3) can be written:      Table 1 summarizes the S(IV) oxidation rates as function of Cr(VI) concentration, temperature and pH dependence. The rate constants (K) determined at pH 2.6 and temperature of 11.0 , 25.0 and 35.0 °C were 1.2 x 10-3 mg-1 L s-1, 4.3 x 10-3 mg-1 L s-1 and 1.1 x 10-2 mg-1 L s-1 respectively. Similar behavior was observed for S(IV) oxidation rate when Mn(II) was employed5. The S(IV) oxidation rate in O2 saturated aqueous solution catalyzed by Cr(VI) is also influenced by acidic media. At pH 2.1 and temperature of 25 °C, the S(IV) oxidation rate is increased by a factor of 5 and 30 when compared to that measured at pH 2.6 and 3.4, respectively. It is known that the oxygen solubility decreases with decreasing pH4 and that there is an equilibrium between HCrO4- and Cr2O72- ions in aqueous solution containing Cr(VI) at pH range 2 to 617. Probably, this observed reaction rate difference can be due to the presence of different chromium species, depending upon the pH. On the other hand, the S(IV) oxidation rate at pH 3.4, or higher, is the same as measured in the absence of Cr(VI) (K = 8.0 x 10-4 s-1). Thus, under these conditions, no catalytic effect was observed.   The activation energy was determined graphically by plotting -ln K vs. 1/T (Fig. 6), at pH 2.6 and temperatures of 11.0, 25.0 and 35.0 °C.respectvely. It was found to be 70.3 kJ mol-1.This value is comparable to that previously determined by Ibusuki and Barnes18 in the presence of Mn(II): Ea = 74.3 kJ mol-1 or that determined by Grgic et al.5 in the presence of Mn(II), Fe(III) and Cu(II): Eac = 63.3 kJ mol-1; Ea = 104 kJ mol-1; Ea = 116 kJ mol-1, respectively. In the more acidic water shells of aerosols or acidic fog and cloud droplets, chromium (VI) - initiated oxidation of sulfur (IV) might be of some importance for the acidification.  Chromium (III)The influence of Cr(III) (1,0 mg L-1) on the oxidation of S(IV) in O2 - aqueous solution was studied at pH 3 and 5.2 and temperature of 25 °C. Under these conditions, inhibitory effect of Cr(III) was observed. Even after six hours the sulfite and sulfate peaks remain constant, and no oxidation reaction could be observed. It is in agreement with the Brandt and Elding19 observations after mixing Cr(III) with tenfold excess of S(IV) at pH 3. A chromium (III)-sulfite complex was formed rapidly. Indeed, Cr(III) only plays a role in the uptake process and that is why it is not catalytically active17.Cadmium (II)The influence of Cd(II) on the oxidation of S(IV) in aqueous phase was studied at pH 3.0 and 5.2 and temperature of 25 °C. The Cd(II) concentrations were 0.2 and 4.4 mg L-1. Independently of the pH and Cd(II) concentration employed, the rate constant was the same as observed in the absence of Cd(II). Thus, no catalytic effect of Cd(II) was observed.Vanadium (V)The influence of V(V) (1,0 mg L-1) on the oxidation of S(IV) in aqueous phase at pH 3.0 and 5.2 and temperature of 25 °C was studied. Under these conditions, an inhibitory effect of V (V) was observed. Even after six hours the sulfite and sulfate peaks remain constant, and no oxidation reaction could be observed. Very little is known about the role of V(V) in atmospheric redox processes17. At pH < 3.0, VO2+ is the dominant V(V) species, and it reacts very slowly with HSO3-. In slightly acidic solutions (4.0 < pH < 6.0) the formation of polyoxovanadates occurs and their influence on the S(IV) oxidation is unknown.ChlorideClarke and Rodojevic14 discovered significant anion catalysis by Cl- (concentrations higher than 35 mg L-1), on S(IV) (3.2 mg L-1 - 0.32 mg L-1) oxidation. On the other hand, Grgic et al. 5 did several experiments using metal chlorides, in the which the Cl- concentrations were lower than 0.35 mg L-1. In this

【 授权许可】

Unknown