DETERMINATION OF LIQUID FILM THICKNESS FOLLOWING DRAINING OF CONTACTORS, VESSELS, AND PIPES IN THE MCU PROCESS

Poirier, M ; Fernando Fondeur, F ; Samuel Fink, S

Savannah River Site (S.C.)

关键词: Fluid Mechanics;    Source Terms;    Testing;    12 Management Of Radioactive Wastes, And Non-Radioactive Wastes From Nuclear Facilities;    Liquid Wastes;   

DOI  :  10.2172/891655
RP-ID  :  WSRC-STI-2006-00031
RP-ID  :  DE-AC09-96SR18500
RP-ID  :  891655

美国|英语

来源: UNT Digital Library

【 摘 要 】

The Department of Energy (DOE) identified the caustic side solvent extraction (CSSX) process as the preferred technology to remove cesium from radioactive waste solutions at the Savannah River Site (SRS). As a result, Washington Savannah River Company (WSRC) began designing and building a Modular CSSX Unit (MCU) in the SRS tank farm to process liquid waste for an interim period until the Salt Waste Processing Facility (SWPF) begins operations. Both the solvent and the strip effluent streams could contain high concentrations of cesium which must be removed from the contactors, process tanks, and piping prior to performing contactor maintenance. When these vessels are drained, thin films or drops will remain on the equipment walls. Following draining, the vessels will be flushed with water and drained to remove the flush water. The draining reduces the cesium concentration in the vessels by reducing the volume of cesium-containing material. The flushing, and subsequent draining, reduces the cesium in the vessels by diluting the cesium that remains in the film or drops on the vessel walls. MCU personnel requested that Savannah River National Laboratory (SRNL) researchers conduct a literature search to identify models to calculate the thickness of the liquid films remaining in the contactors, process tanks, and piping following draining of salt solution, solvent, and strip solution. The conclusions from this work are: (1) The predicted film thickness of the strip effluent is 0.010 mm on vertical walls, 0.57 mm on horizontal walls and 0.081 mm in horizontal pipes. (2) The predicted film thickness of the salt solution is 0.015 mm on vertical walls, 0.74 mm on horizontal walls, and 0.106 mm in horizontal pipes. (3) The predicted film thickness of the solvent is 0.022 mm on vertical walls, 0.91 mm on horizontal walls, and 0.13 mm in horizontal pipes. (4) The calculated film volume following draining is: (a) Salt solution receipt tank--1.6 gallons; (b) Salt solution feed tank--1.6 gallons; (c) Decontaminated salt solution hold tank--1.6 gallons; (d) Contactor drain tank--0.40 gallons; (e) Strip effluent hold tank--0.33 gallons; (f) Decontaminated salt solution decanter--0.37 gallons; (g) Strip effluent decanter--0.14 gallons; (h) Solvent hold tank--0.30 gallon; and (i) Corrugated piping between contactors--16-21 mL. (5) After the initial vessel draining, flushing the vessels with 100 gallons of water using a spray nozzle that produces complete vessel coverage and draining the flush water reduces the source term by the following amounts: (i) Salt solution receipt tank--63X; (ii) Salt solution feed tank--63X; (iii) Decontaminated salt solution hold tank--63X; (iv) Contactor drain tank--250X; (v) Strip effluent hold tank--300X; (vi) Decontaminated salt solution decanter--270X; (vii) Strip effluent decanter--710X; (viii) Solvent hold tank--330X. Understand that these estimates of film thickness are based on laboratory testing and fluid mechanics theory. The calculations assume drainage occurs by film flow. Much of the data used to develop the models came from tests with very ''clean'' fluids. Impurities in the fluids and contaminants on the vessels walls could increase liquid holdup. The application of film thickness models and source term reduction calculations should be considered along with operational conditions and H-Tank Farm/Liquid Waste operating experience. These calculations exclude the PVV/HVAC duct work and piping, as well as other areas that area outside the scope of this report.