期刊论文详细信息
Advances in Materials Science and Engineering 卷:2026
Spark Plasma Sintering of Low-Density Stainless Steel: Optimisation of Sintering Parameters
Research Article
Dineo Mosoma1  Vhonani Munyangane1  Rasidi Sule2  Desmond Klenam1  Moses Avwerosuoghene Okoro3  Michael Oluwatosin Bodunrin1 
[1] Next Frontiers in Advanced Materials Laboratory, School of Chemical and Metallurgical Engineering, University of the Witwatersrand, Johannesburg, South Africa, wits.ac.za
[2] Department of Engineering Metallurgy, University of Johannesburg, Johannesburg, South Africa, uj.ac.za
[3] Department of Physics, Covenant University, Ota, Nigeria, covenantuniversity.edu.ng
关键词: low density;    microstructure;    spark plasma sintering;    stainless steel;   
DOI  :  10.1155/amse/8536362
 received in 2025-12-04, accepted in 2026-07-01,  发布年份 2026
来源: Hindawi Publishing Corporation
PDF
【 摘 要 】

The study was conducted to determine the optimised sintering conditions for producing low-density stainless steel via powder metallurgy route. Low-density Fe–Mn–Al–Cr–C stainless-steel alloys containing Mo and Cu were produced from commercially available elemental powders via mechanical alloying followed by consolidation using spark plasma sintering (SPS). Four alloy compositions under varying sintering parameters, including temperature (900°C–1100°C), dwell time (5–7 min) and pressure (40–50 MPa), were explored. Electrochemical testing, including open-circuit potential (OCP) and cyclic polarisation (CP), was performed in 0.9% NaCl to evaluate corrosion susceptibility. Characterisation of both the mechanically alloyed powders and the sintered alloys was performed using scanning electron microscopy–backscattered electron imaging, scanning electron microscopy–energy-dispersive X-ray spectroscopy and X-ray diffraction. The XRD patterns of the mechanically alloyed powders revealed the presence of two phases, austenite and ferrite, together with the formation of Mo-enriched precipitates. Results indicated that sintering temperature, pressure and dwell time had a significant effect on the final density, which increased with higher parameter values. The sintered alloys achieved relative densities between approximately 94% and 100%. The porosity ranged from 0.01% to 5%. Microstructural examination indicated that the alloys consist mainly of a duplex configuration made up of γ-austenite with an FCC crystal structure and α-ferrite with a BCC structure. In addition, precipitates enriched in Cr and Mo were identified particularly in Alloys 3 (Fe–30.67Mn–2.39Al–4.23Cr–0.09C–5.20Mo–3.44Cu wt%) and 4 (Fe–21.55Mn–3.78Al–4.12Cr–0.22C–5.30Mo–3.51Cu wt%). Among all compositions, Alloy 1 (6Fe-31.49 Mn-2.45 Al-4.34 Cr-0.09 C wt%) demonstrated the best overall sintering response, microstructural quality and corrosion resistance, achieving a high density of 99.4% (Alloy 1C) and a low corrosion rate of 0.087 mm/yr (Alloy 1D). The optimum sintering conditions were determined to be 1100°C and 50 MPa for Alloys 1 (Fe-31.49Mn-2.45Al-4.34Cr-0.09C wt%) and 2 (Fe-22.14Mn-3.88Al-4.23Cr-0.23C wt%) and 900°C and 50 MPa for Alloys 3 (Fe-30.67Mn-2.39Al-4.23Cr-0.09C-5.20Mo-3.44Cu wt%) and 4 (Fe-21.55Mn-3.78Al-4.12Cr-0.22C-5.30Mo-3.51Cu wt%).

【 授权许可】

CC BY   
Copyright © 2026 Dineo Mosoma et al. Advances in Materials Science and Engineering published by John Wiley & Sons Ltd. 2026

【 预 览 】
附件列表
Files Size Format View
RO202609140001328ZK.pdf 24202KB PDF download
RO202609140000301ZK.pdf 1012KB PDF download
RO202609140000306ZK.pdf 967KB PDF download
Figure 1 74KB Image download
Figure 3 78KB Image download
Figure 3 68KB Image download
Figure 4 55KB Image download
Figure 7 53KB Image download
Figure 9 74KB Image download
Figure 10 88KB Image download
Figure 3 130KB Image download
Figure 4 95KB Image download
Figure 1 64KB Image download
【 图 表 】

Figure 1

Figure 4

Figure 3

Figure 10

Figure 9

Figure 7

Figure 4

Figure 3

Figure 3

Figure 1

【 参考文献 】
  • [1]
  • [2]
  • [3]
  • [4]
  • [5]
  • [6]
  • [7]
  • [8]
  • [9]
  • [10]
  • [11]
  • [12]
  • [13]
  • [14]
  • [15]
  • [16]
  • [17]
  • [18]
  • [19]
  • [20]
  • [21]
  • [22]
  • [23]
  • [24]
  • [25]
  • [26]
  • [27]
  • [28]
  • [29]
  • [30]
  • [31]
  • [32]
  • [33]
  • [34]
  • [35]
  • [36]
  • [37]
  • [38]
  • [39]
  • [40]
  • [41]
  • [42]
  • [43]
  • [44]
  • [45]
  • [46]
  • [47]
  • [48]
  • [49]
  • [50]
  • [51]
  • [52]
  • [53]
  • [54]
  • [55]
  • [56]
  • [57]
  • [58]
  • [59]
  • [60]
  • [61]
  • [62]
  • [63]
  • [64]
  • [65]
  • [66]
  • [67]
  • [68]
  • [69]
  • [70]
  • [71]
  • [72]
  • [73]
  • [74]
  • [75]
  • [76]
  • [77]
  文献评价指标  
  下载次数:0次 浏览次数:0次