期刊论文详细信息
Advances in Mechanical Engineering
Mathematical modeling and forming method of rake face of toroidal worm gear hob based on conical production surface
Research Article
Saixuan Chen1  Guohua Cui2  Zhenshan Zhang2  Jie Yang2 
[1] Saixuan Chen, Shanghai Collaborative Innovation Center of Intelligent Manufacturing Robot Technology for Large Components, School of Mechanical and Automotive Engineering, Shanghai University of Engineering Science, No. 333 Longteng Road, Songjiang District, Shanghai 201620, China. Email: ;Shanghai Collaborative Innovation Center of Intelligent Manufacturing Robot Technology for Large Components, School of Mechanical and Automotive Engineering, Shanghai University of Engineering Science, Shanghai, China;
关键词: Toroidal worm gear hob;    rake face;    rake angle;    conical production surface;    mathematical modeling;   
DOI  :  10.1177/16878132221131298
 received in 2022-07-22, accepted in 2022-09-16,  发布年份 2022
来源: Sage Journals
PDF
【 摘 要 】

In order to improve the cutting performance of toroidal worm gear hob and the tooth surface accuracy of hobbing worm gear, to control the absolute value of the side rake angle of each cutter tooth to be smaller and more balanced on the left and right sides, a method of developing the rake face of toroidal worm gear hob with spiral groove by using conical production surface is proposed. According to the theory of gear meshing rationality, the mathematical model of the rake face is established. The analysis and calculation example results show that the absolute value of the rake angle on both sides changes with the transmission ratio coefficient. By studying this change law, the optimal milling transmission ratio coefficient k = 0.886 is obtained. Meanwhile, the corresponding absolute value of the rake angle is between ±4.5°, which reduce the absolute value of the rake angles on both sides of the cutter teeth effectively and make the rake angles on the left and right sides be more balanced. The spiral groove was simulated, and the rake angle was measured in the simulation software. The measured results are consistent with the calculated results, which prove the correctness of this method.

【 授权许可】

CC BY   
© The Author(s) 2022

【 预 览 】
附件列表
Files Size Format View
RO202212209999364ZK.pdf 2421KB PDF download
Figure 3. 57KB Image download
Table 1. 204KB Table download
Table 5. 415KB Table download
Figure 1. 469KB Image download
Figure 5 45KB Image download
Table 3. 514KB Table download
Table 1. 575KB Table download
Figure 1 26KB Image download
Figure 3. 215KB Image download
Table 4. 451KB Table download
Figure 3 53KB Image download
Figure 5. 199KB Image download
Figure 8. 554KB Image download
Table 3. 437KB Table download
Table 2 72KB Table download
Table 3 63KB Table download
Table 4 45KB Table download
Figure 10. 358KB Image download
Table 1. 134KB Table download
Table 6. 466KB Table download
Table 2 44KB Table download
Table 2 68KB Table download
Table 3 53KB Table download
【 图 表 】

Figure 10.

Figure 8.

Figure 5.

Figure 3

Figure 3.

Figure 1

Figure 5

Figure 1.

Figure 3.

【 参考文献 】
  • [1]
  • [2]
  • [3]
  • [4]
  • [5]
  • [6]
  • [7]
  • [8]
  • [9]
  • [10]
  • [11]
  • [12]
  • [13]
  • [14]
  • [15]
  • [16]
  • [17]
  • [18]
  • [19]
  • [20]
  • [21]
  • [22]
  • [23]
  • [24]
  • [25]
  • [26]
  • [27]
  • [28]
  • [29]
  • [30]
  • [31]
  文献评价指标  
  下载次数:31次 浏览次数:0次